Accessories Please note: All-Pitch means flat to 5/12
All-Pitch Plumbing / Electrical Flashing
Standard Flashings are generally acceptable
for use with steel and soil pipe, ABS, PVC, plastic or EMT electric
metal tubing. Drain waste vent uses 6/12 - 12/12 pitch.
FHA Standards require the FHA flashing, depending on the roof covering
or other factors. Please check local codes
Available in the following:
Sizes ½ to 4"
All-Pitch Heating Vent Flashing
Standard Flashings are generally acceptable
for composition or shingle roofs unless pitch of roof, shingle exposure
or roofing material is unusual.
FHA Standards require the FHA flashing, depending on the roof covering
or other factors. Please check local codes.
Available in the following:
Sizes: 3" through 20"
Aluminum Flashing
Aluminum Flashings are available for
steel pipe, Drainage Waste Vent, AmeriVent conductor, soil pipe or
transite.
Available in the following:
Sizes:
.02 Dead Soft Base ½" to 8"
Oval Dead Soft 4" to 6"
Standard ½ Hard Riser
Durable, all galvanized steel constructed
cap is used with conductor pipe.
Available in the following:
Sizes: 3" through 8"
Conductor Pipe Caps
Durable, all galvanized steel constructed
cap is used with conductor pipe.
Available in the following:
Sizes: 3" through 8"
Round, Adjustable Storm Collars
Storm Collars are used with flashings
to insure water-tight installation. Use with conductor or transite
pipe and seal the collar to the pipe.
Available in the following:
Sizes: 3" through 18"
Vent Collars
Vent collars provide cover for rough
wall openings and fits conductor pipe.
Available in the following:
Sizes: 3" through 7"
Wall Thimbles
Wall Thimbles adjust for various wall
thicknesses from 4" to 6" and provide proper clearance for
venting from combustibles. Thimbles are sized for conductor pipe.
Available in the following:
Sizes: 3" through 7"
Conductor and Vent Pipes
Single Wall Pipe features rugged construction
of corrosion-resistant galvanized steel.
Available in the following:
Sizes: 3" through 6" Conductor Pipe
Lengths: 10'
Sizes: 3" through 12" Vent Pipe
Lengths: 30"
Bell-type Single Wall Increasers
Increasers are used to increase vent
size up to 3".
Available in the following:
Sizes: 3" to 10"
Bell-type Single Wall Reducers
Reducers are used to decrease vent
size by 2".
Available in the following:
Sizes: 8" to 3"
Adjustable 90° Single Wall Elbow
Adjustable elbows are constructed of
sturdy galvanized steel.
Available in the following:
Sizes: 3" through 12"
Single Wall Vent Tee
Tees feature identical trunk and branch
diameters. For smaller applications, use a reducing tee. For larger
applications, use an increaser with this standard tee.
Available in the following:
Sizes: 3" through 8"
Single Wall Vent Wye
Wyes feature identical branch, truck
and base diameters and are used to vent more than one appliance.
Available in the following:
Sizes: 3" through 8"
Type BW Attic Shield
Type BW Attic Shields are to be used
on single-story or on top story of multi-story buildings for Type
BW Gas Vent. Los Angeles Code and UMC requires a 26 gauge galvanized
sleeve to extend from the top of the ceiling plate into the attic.
Required by Los Angeles Code and UMC
Plate Straps
Black Plate Straps are bundled in packs
of 50.
Available in the following:
12 and 16 gauge
Lengths: 9", 12", 18", 24"
Pipe Straps
Straps are used for securing metal
pipes into position.
Available in the following:
Sizes ½ to 4"
Hanger Iron
1" x 10' Hanger Iron is constructed
from galvanized steel.
Available in the following:
Size: 1" x 10'
18 Gauge
Flue Stops
Flue stops are used to cover existing
flue holes.
Available in the following:
Sizes 3" to 6"
Plumber's Tape
Plumber's Tape is a convenient method
to secure vents into position.
