Ameri-Tec® chimney pipe sections combine corrosion-resistant stainless steel and sturdy galvanized steel for strong chimney construction. Lightweight and snap-lock joints offer faster, easier installations. Chimney sections are also available with a stainless steel outer wall for corrosive environments, Model HSS.
Available in the following:
Size 6" and 8"
Length 12", 18", 24" and 36"
Caps
Durable, all stainless steel constructed cap is designed to minimize downdraft. Features its own spark arrestor and bird debris screen.
Available in the following:
Sizes 6" and 8"
Offsets
For use in pairs to permit chimney to “go around” joist, rafters or other projections. Add chimney sections between offsets to produce additional offset. Click here for the chimney offset chart.
Available in the following:
Sizes 6" and 8"
Angles 15°
and 30°
Attic Insulation Shield
Required shield for use in unoccupied attic areas to prevent
insulation material from infringing on the 2 in. air space clearance.
Available in the following:
Sizes 6" and 8"
Firestop Assembly
Firestop is required at each floor level, except at ceiling support or roof support. Provides correct spacing to combustible
materials as the chimney passes through a combustible floor.
Available in the following:
Sizes 6" and 8"
Single Wall Adaptor
Included in ceiling support assembly, roof support assembly and tee assembly for easier installation of single wall
connector pipe. Stainless Steel. Flat black finish.
Available in the following:
Sizes 6" and 8"
Wall Thimble
Used with tee branch and chimney section to provide proper clearance to combustible materials. Flat black painted surface for interior wall eliminates need for trim plate.
Available in the following:
Sizes 6" and 8"
Storm Collar
Use with flashings to insure water-tight installation. Multi-size collar fits both 6" and 8" chimneys.
Available in the following:
Sizes 6" and 8"
Round Flashing
Available in galvanized and aluminum models flat to 6/12
pitch (Standard) and for steeper pitches of 7/12 to 12/12
pitch, 13/12 to 18/12 pitch and 19/12 to 24/12 pitch.
Available in the following:
Sizes 6" and 8"
Tall Flashing
For flat to 1/12 pitch roofs. Use on flat roofs in snowpack
areas to reduce chances of leakage.
Available in the following:
Sizes 6" and 8"
Supports
Ceiling Assembly
Use when chimney is installed in flat ceiling. 6" and 8"
sizes fit between regular 16" O.C. ceiling joists. Cartoned
to contain stainless steel flat black single wall adaptor.
(For exposed-beam ceiling installations, use Roof Support Assembly.) Flat black finish.
Available in the following:
Sizes 6" and 8"
Face Plate
Decorative trim collar that conceals the rough opening where the support passes through ceiling. Flat black finish.
Available in the following:
Sizes 6" and 8"
Anchor Plate
Use to support and connect chimney sections to a masonry
firebox or an appliance which is specifically listed for direct
connection to an Ameri-Tec® Anchor Plate and chimney system.
Available in the following:
Size 8" HS
Size 10" FB - AmeriVent Model
Roof Assembly
For exposed-beam ceiling installations. Cartoned to contain
stainless steel flat black single wall adaptor. (Use ceiling
support assembly when chimney is to be installed in flat ceiling.) Flat black finish.
Available in the following:
Sizes 6" and 8"
Roof Brace Kit
Available in the following:
Sizes 6" and 8"
Use for tall chimneys or in windy areas to stabilize chimney above the roof.
Wall Support with Cleanout
Supports chimney tee and chimney. Attach brackets to wall above or below heavy gauge base plate. Includes insulated tee cap.
Available in the following:
Sizes 6" and 8"
Bracket
Bracket for supporting chimney pipe offset, or for securing outdoor chimney to exterior wall while maintaining proper
2 in. clearance to wall.
Available in the following:
Sizes 6" and 8"
Tees
Chimney Tee Assembly
Chimney tee, tee branch (made up of one 12 in. section of chimney), single wall adaptor, pipe end plate and tee cap. Use this combination where connection to chimney is made into branch of tee in “Through-the-Wall” installation.
Available in the following:
Sizes 6" and 8"
Chimney Tee
Consists of chimney tee and tee cap in galvanized or stainless steel outer wall.
